Crankcase 1 Clean crankcase with soft agent completely 2 Clean all sealing surfaces and closing sur- faces completely 3 Inspection:. Inject the clean solvent ¢Ù into intake way and exhaust way respectively. Mount: ¡¤ Spring ¢Ù ¡¤ Foot rest ¢Ú right Bolt foot rest 65Nm 6. Resistance value of charge coil. Mount: ¡¤ Cylinder ¢Ù ¢Ù ¡¤ Tighten bolt cylinder temporally Caution ¡¤ When pressing the piston ring with one hand, assembly the cylinder with another one. Valve cap ¢Ù Side of outlet door b. Free length of clutch spring If not of specification replace a set of spring Min Limit of clutch spring length 32.
Driving gear of balance shaft ¢Ù. Inspection One of parts of O-ring¢Ù , compressure spring ,rough filter ¢Û ,fine filter ¢Üis damaged, repalce it. Mount the rear wheel axle, rear brake, rear ¢Ù brake hub, right rear wheel, rear wheel joint plate and left rear wheel. Place an oil catcher under the rear driving gear case. Only enough examining distance Suggestion ¡Ý. ¢Û 3 Mount Washer ¢Ù ¢Ü ¡¤ Reverse gear ¢Ú ¢Û ¢Ú.
Installment Barke shoe assy 9. Connect as shown in figure ¢ÙSpark testing instrument ¢ÚSpark plug cap ¢ÛSpark plug. Closed clearance of piston ring. By that, you can disassemble the cushion. ¡¤ The timing chain should through the bend- ing locking end ¢Ú of chain chamber.
Take off dusty cap on rear arm axle ¢Ù. The following types of tires reliability by our company be used safely by this motorcycle. Remove some parts before maintenance 1 Cushion Pocket multimeter. Pre-heat engine for 5 minutes or more, and then stop. Start the power for electrical appliance inspection. Take off left rear wheel, rear wheel joint plate right rear wheel rear brake hub, rear brake and rear wheel axle. Loosen the locking nut ¢Ù.
Engine oil fine filter gal clutch 3. Check the gear case lower cap, if there is one of crack bend damagement problems, re- place this part. Check if bulb and bulb socket is correct Replace bulb and bulb socket Pass No electrification 2. It is fully printable, print 1 page, 1 chapter or print the entire manual and put it in a 3-ring binder. All the closing case screw. Check if the rear wheel fork assy is crack bend and damaged, if any, replace it.
Fasten: ¡¤ Bolt ¢Ù Installation position of engine-rear lower ¡¤ Bolt ¢Ú Installation position of engine-rear lower ¡¤ Bolt ¢Û Installation position of engine-front ¡¤ Bolt ¢Ü Installation position of engine-top ¡¤ Coupling bolt of rear arm ¢Ý Rear arm shaft-right ¡¤. Free clearance of left lever. Reverse fork shaft ¢Ù ¢Ù ¢Ú. Put the vehicle on the flat ground. Resistance value of ignition coil 9.
Check of electirc parts 7. Inspection ¢Ù If cracks beat,damaged,replace it. And increase the spark clearance until the engine can not be started. Movement of fork on the fork shaft ¢Ù. Check local laws before riding on trails. Lubrication part ¢ÙOil seal lip of rear wheel axle. Rest the motorcycle on the flat ground 2.
Clutch case assy ¢Ù inner surface Ablation,wear or darmage,replace it. Removal ¢ÚBolt M8 ¡Á60 ¢ÛLocking washer ¢ÜClip assy 3. Install Brake shoe assy Do not apply lubricating grease on brake fric- tion wafer. Don't pay dealer retail for an overpriced book! Reverser diameter Not conforming to specification ¡úchange the startig motor Outer diameter 28mm 1. Remove the relay from cable. Change the shift to the 1st gear, and pull the steering lever ¢Ùto reverse gear position.
Remvoe the air ¢Ù air case of last grade and rear brake hub from the clip on the frame. Disassemble the valve lock clip with valve spring compressing device. Screw ¢Ù rear driving cover ¢Ú. Attached:The radial runout limit of rear wheel axle:1. Gear refer to shift mechanism and output gear ¢Ú. Remocal Install the steering vertical column with split 2.